X Micro Tech Headphones BT400GII User Manual

X-Micro Bluetooth Headset  
User Manual  
1
 
Introduction  
The X-Micro Bluetooth Headset is a most desirable gadget to connect with  
your Bluetooth mobile phone cordlessly.  
By wearing X-Micro Bluetooth Headset, it becomes most effortless for making  
a call or receiving a call without handling your mobile phone, moreover, makes  
the communication naturally.  
The imperceptible Bluetooth connection can be up to 10 meters and doesn’t  
need line of sight and get rid of annoying cable for good.  
The X-Micro Bluetooth Headset can be used with any mobile phone which  
supports the Bluetooth  
 
Headset profile  
General Ratio  
Carrier Frequency : 2.4 ~ 2.480GHz  
Ratio Performance – Receiver  
Rx sensitivity < -80 dBm  
Ratio Performance:  
CSR BC02 audio Class II Chipset  
Spread Spectrum  
FHSS (Frequency Hopping Spread Spectrum)  
Antenna  
Chip Antenna  
Environmental  
Operating Temperature 0 ~ +55  
Dimensions & Weight  
92mm(L) x 50mm(W) x 26mm(H); 26g  
LED Indicator Status  
Blue: Power on mode;  
Red: Low power or being charged  
Blue & Red: Pairing mode  
Power Spec.  
5V / 500mA  
Battery  
3.7V / 160mA  
Standby time/ Talk time  
100hours / 4hours  
 
Overview of X-Micro Bluetooth Headset  
”Volume Up ” Button  
”Volume Down ” Button  
”Power / Talk / Pairing ” Button  
Open / Close the microphone  
The microphone can be closed when the  
headset doesn’t use.  
DC Power In  
Earhook  
Speaker  
Microphone  
Changing the Earhook  
The X-Micro Bluetooth headset can be worn on either ear. Please carry out the  
following steps to shift the ear hook for wearing it on the other ear.  
1. Carefully remove the earhook from the  
headset  
2. Change the direction of the earhook as  
shown in diagram 2.  
3. Carefully replace the earhook on the  
headset.  
 
Turning the Headset ON/OFF  
To turn your headset ON:  
Press and hold the power button  
for 3 seconds, and then the speaker  
will emit two high tones. When the power is on, the LED in the power button  
starts to flash blue.  
(Note: The headset will go to pairing mode if you press and hold the power  
button for 5 seconds from OFF status)  
To turn your headset OFF:  
Press and hold the power button  
for 3 seconds, and then the speaker  
will emit two high tones. When the power is off, the LED in the power button  
stops flashing.  
Charging the Battery  
Before using X-Micro Bluetooth Headset you will have to charge the battery for  
approximate 3 hours to ensure a fully charged battery.  
1. Plug the AC power adapter into the DC POWER IN socket situated at the  
back of the headset.  
2. Plug the AC power adapter’s plug into an electrical wall outlet.  
3. When charging, the LED in the power button  
charging is complete.  
is on and remains lit until  
4. Charge the headset for approximate 3 hours or until the LED in the power  
button extinguishes.  
5. Remove the AC adapter from the headset’s AC power jack.  
Notice: The headset doesn’t work while it’s charging.  
 
Pairing to a Bluetooth Phone  
What is Bluetooth Pairing?  
Before using your headset for the first time, you must pair it with a particular  
Bluetooth cell phone previously. ”Pairing” process creates a unique wireless  
link between two devices. Once paired, the communication between two  
devices does not need any authentication or authorization anymore.  
Please follow the instruction below to pair the headset with a Bluetooth cell  
phone:  
1. Ensure the headset is OFF.  
2. Press and hold the power button  
for approximately 5 seconds until the  
headset LED starts to flash with blue and red.  
3. Release the power button  
when the LED is flashing, the status  
indicates that the headset is in pairing mode and waiting to pair with  
another Bluetooth device.  
4. Follow the operating instructions for your Bluetooth phone to start a pairing  
process.  
5. Your phone’s display will indicate that it found one or more Bluetooth  
devices, the “X-Micro Bluetooth Headset” should be included in the list,  
please select it for pairing.  
6. The phone’s display then prompt you for a pairing passkey or PIN, please  
enter four zeros “0000”  
7. When the pairing process is finished successfully, the headset LED will  
return to normal status of flashing blue only.  
8. Your phone’s display may ask you whether you want to change the headset  
name; you can replace the” X-Micro Bluetooth Headset” with any you may  
prefer.  
 
Answering/Ending a Call  
Answering a Call  
After being paired with your cell phone, the headset is now ready to receive  
incoming calls without handling the phone. When there’s an incoming call, both  
the cell phone and the headset will ring simultaneously. Upon hearing the ring  
tones through the headset’s speaker you can answer the incoming call by  
pressing power button  
and then speaking normally.  
Ending a Call  
You can use either of the ways to end a call:  
1. Press the headset’s power button  
to end a call.  
2. Press the phone’s keypad to end a call.  
 
Making a Call  
There are two ways to make calls:  
1. Using the phone’s keypad:  
As general usage, dial the phone number you want to call by pressing the  
phone’s keypad. You may also hear the dialing tones through the headset.  
2. Using the Voice Dialing through the headset:  
What is voice dialing?  
Voice dialing is a feature on some Bluetooth phones which allows you make  
calls by saying the name of the person you want to call. The phone compares  
your voice with your previous recording (called a voice tag). If they match then  
the phone will automatically dial the corresponding phone number.  
Not all Bluetooth phones support voice dialing, please refer to your phone spec  
to make sure whether your phone supports this feature.  
The headset does not have a keyboard so it necessary to use voice dialing to  
make calls. To do this you have to record voice tags for the contacts in your  
phone address book.  
If your phone supports voice dialing function, you can use this feature with the  
headset easily. Note that the voice dialing on your phone must be enabled and  
the voice tags must have been recorded previously. (Please refer to your  
phone instruction on recording and storing voice tags)  
II. Briefly press the button once.  
III. After the tone, say the name of the person you want to call.  
IV. The phone number will be dialed automatically by phone after  
recognizing the correct voice tag.  
 
Play Audio CD, MP3  
1. Prepare your computer  
Make sure the Bluetooth software is well-installed in your computer and the  
Bluetooth device is plugged in.  
What you need with playing music from the computer:  
I. A Bluetooth Device which supports Bluetooth Headset profile.  
Ex. X-Micro Bluetooth USB Dongle (Class 2) / (Class 1)  
II. A Bluetooth software which supports Bluetooth Headset profile.  
Ex. Widcomm 1.3.2.7  
III. A Bluetooth headset which supports Bluetooth Headset profile.  
Ex. X-Micro Bluetooth USB Dongle  
2. Paring X-Micro Bluetooth Headset with your computer  
I. Make X-Micro Bluetooth Headset become pairing mode.  
a. Make sure X-Micro Bluetooth Headset is power off.  
b. Press the power button for 5~7 seconds  
c. When the light flashes red and blue, X-Micro Bluetooth Headset is  
in the pairing mode.  
II. Find X-Micro Bluetooth Headset from the computer.  
Ex. Widcomm 1.3.2.7  
a. Right click on the Bluetooth icon.  
b. Select “Quick Connect”.  
c. Select “Headset”.  
d. Select “Find Devices…”.  
 
III. Connect X-Micro Bluetooth Headset.  
You will see a X-Micro Bluetooth Headset  
device on the searching windows after the  
searching mode,  
a. Select “X-Micro Bluetooth Headset”.  
b. Click “Connect”.  
IV. Input the PIN code for the request.  
a. Click the Bluetooth icon.  
b. When the “Bluetooth PIN Code  
Request” window appears, enter “0000”  
(4 zeros).  
c. Click “OK”.  
V. Complete creating a connection shortcut.  
a. Click “OK” on “My Bluetooth Places”  
window.  
b. Click “OK” on “Bluetooth Service”  
window.  
VI. Configure Audio Output  
a. Open “Control Panel” window  
b. Double click on “Sound and Audio  
Device”  
c. Select “Audio”  
d. Change Sound playback to “Bluetooth  
Audio”  
e. Change Sound recording to “Bluetooth Audio”  
f. Click “OK”  
 
3. Listen to music from X-Micro Bluetooth Headset  
I. Play Audio CD  
a. Connect the X-Micro Bluetooth Headset with the computer:  
- Make sure the headset is power on.  
- Press the power button 1 time.  
- Wait for about 3 seconds the headset will reconnect with the  
computer.  
b. Put the Audio CD in CD ROM.  
c. Run “Windows Media Player”  
d. Play the Audio CD  
II. Play MP3  
a. Connect the X-Micro Bluetooth Headset with the computer:  
- Make sure headset is power on.  
- Press the power button 1 time.  
- Wait for about 3 seconds the headset will reconnect with the  
computer.  
b. Double click on the MP3 file.  
c. The MP3 file will be played.  
 
Appendix I  
Button Function  
Power Button Turn ON/OFF  
Press the power button for 3 seconds until the  
blue LED flashes five times.  
Answer/End calls Press the power button once  
Pairing  
When the headset is off, press the power  
button to turn on and keep it pressed for  
about 5 se4conds until the LED flashes blue  
and red alternately.  
Down/Up Button Volume control  
Press the UP or DOWN button repeatedly  
until you reach your desired level.  
Press the UP or DOWN button for about 2  
seconds  
/
Mute/Unmute  
Appendix II  
Audio Tone  
Turn On  
Turn Off  
Two high tones  
Two low tones  
Pairing mode Two High tones  
Incoming Call A ring tone at 2 seconds interval  
Repeated two low beeps at 3 seconds  
Mute  
interval  
Unmute  
A single beep  
Start when the talk time is left about 3-5  
minutes. At a 16 seconds interval  
Battery low  
 

Weed Eater Trimmer 545117522 User Manual
Weslo Treadmill WLTL332050 User Manual
Whirlpool Freezer EV181NZRQ User Manual
Whirlpool Range 9762365A User Manual
Whirlpool Trash Compactor TF 4500 Senes User Manual
White Rodgers Thermostat 1F80 0224 User Manual
White Rodgers Thermostat 50A66 743 User Manual
Xoro DVD Player HSD 2200 User Manual
Xtant Speaker X1244 User Manual
Zanussi Dishwasher 132519 User Manual