Barco Crib Toy RCP120 User Manual

Barco, Inc.  
Toll Free: +1 (888) 414-7226  
Fax: +1 (916) 859-2515  
Technical Support: +1 (866) 374-7878  
11101 Trade Center Drive  
Rancho Cordova, CA  
95670 • USA  
Quick Start Guide  
Visibly yours  
RCP-120 Installation: System Connections  
For detailed installation instructions, refer to Chapter 2 of  
the RCP-120 User’s Guide.  
Ethernet Switch  
To FSN-1400  
DC  
Power  
Script  
Light  
12V DC OUT  
1.5A  
Ethernet  
Port 1  
Ethernet  
Port 2  
AC  
Power  
RCP-120 Rear  
Panel  
Touch Screen  
Connector Panel  
USB  
DVI-D  
12V DC  
FSN-150 Rear  
Panel  
Cable Harness  
RCP-120 Setup  
Understanding Button Color  
Communications Setup — Make sure each RCP-120 has a  
unique IP Address, compatible with the FSN network. Use a  
computer attached to the same network to browse to the RCP-  
120 Web Interface and change the IP Address if necessary.  
Refer to Chapter 3 in the RCP-120 User’s Guide.  
5
RCP-120 setup is comprised of 10 sequences,  
each of which includes several steps.  
Remote Panel Name — (Optional) Give the RCP-120 a  
unique name. Browse to the RCP-120 Web Interface and  
update the Host Name to uniquely identify each panel. Refer  
to Chapter 3 in the RCP-120 User’s Guide.  
For error-free setup, always refer to either the  
FSN User’s Guide, indicated by the blue circles or the  
RCP-120 Users Guide, indicated by the green circles.  
6
7
Setup Panels in the FSN Controller — On the Assign  
Remote Panels Menu, under the System, Other Setup Menu,  
press {Discover Remote Panels} to search the FSN network  
and populate the Remote Panel Table. Refer to Chapter 4 in  
the RCP-120 User’s Guide.  
General FSN System Setup — Follow the steps outlined in  
Chapter 6 of the FSN User’s Guide to setup the FSN System  
before connecting the RCP-120 devices.  
1
Assign Aux Outputs — On the Assign Remote Panels Menu,  
select the appropriate RCP-120 panel and press the {Assign  
Aux} button. In the Select Aux Output Pop-up that appears,  
select the Aux Output that will be controlled by this RCP-120.  
Repeat this step for any additional devices. When finished,  
press the {Close} button to clear the pop-up.  
8
FSN Aux Setup — Refer to Aux Setup in Chapter 6 of the  
FSN User’s Guide to configure the Aux Outputs on the FSN  
system.  
2
Saving the Setup — On the System Menu, press {Save All} to  
save all system parameters to non-volatile memory, including  
input and output setups, button mappings, tallies, user  
preferences and more. Refer to Chapter 6 in the FSN User’s  
Guide.  
Verify Aux Output Configuration — Ensure the Aux Outputs  
are working as expected by following the steps outlined in the  
Working with Aux Buses section in Chapter 7 of the FSN  
User’s Guide.  
9
3
Install the RCP-120 Devices — Use a standard Ethernet  
cable to connect the LAN port on the RCP-120 to the  
Ethernet switch used to connect the FSN-1400 and Ethernet  
Port 1 of the FSN Controller.  
Backing up the System — Insert a USB drive into the USB  
Port. On the Backup and Restore Menu, press {Backup  
System} to back up the system setup and all memory registers.  
Refer to Chapter 6 in the FSN User’s Guide.  
4
10  
P/N 26-1004005-00, Rev 00  

Grizzly DVD VCR Combo g0748 User Manual
FUNAI CR270TT8 User Manual
Dell Precision 380 User Manual
Cypress CY7C1218H User Manual
Cypress CY7C1156V18 User Manual
COBY electronic CX24 User Manual
AT T EL52350 User Manual
Asus PENTIUM P2B F User Manual
AMX Modero NXD 700Vi User Manual
Adesso MKB 125B User Manual